Rubbermaid glue report: Forget Gorilla Glue

It dries very brittle, and just chips right off the rubbermaid. I did find a
great simple waterproof seal though for adding a cap to t a toilet flange..
it fits on, but not waterproof, and I didn't want to glue it, in case I want
to cannibalize parts down the road. A simple wrap of duct tape around worked
great to seal the minute space there.

Thinking of trying hot melt glue, or pvc glue next on the rubbermaid.

Can't really assemble the rubbermaid filter without some gluing/sealing
solution.

--
Gareee
(Gary Tabar Jr.)

In article <>,
"Gareee©" <gareee-> wrote:

> It dries very brittle, and just chips right off the rubbermaid. I did find a
> great simple waterproof seal though for adding a cap to t a toilet flange..
> it fits on, but not waterproof, and I didn't want to glue it, in case I want
> to cannibalize parts down the road. A simple wrap of duct tape around worked
> great to seal the minute space there.
>
> Thinking of trying hot melt glue, or pvc glue next on the rubbermaid.
>
> Can't really assemble the rubbermaid filter without some gluing/sealing
> solution.

How about a good silicone glue? (Like aquarium sealer)

--
To reply by email, remove the word "space"

> How about a good silicone glue? (Like aquarium sealer)

Tar like substance might do better as it would give a flexible bond.
>
> --
> To reply by email, remove the word "space"

The compression of a rubbery substance is a wothwhile direction. We
have one berm pond with a toilet flange as the exit. It is rather
like a burger: The flange is the outer layer (bread/bun). Then two
layers of EDPM, coated with roofing sealer on either side and between
(lettuce and tomatoes?). Then the plastic (burger in the center). It
repeats on the other side with two layers of EDPM and a flat toilet
ring. The flange and the ring are held together by stainless steel
bolts and washers. The bolts compress the edpm and tar, resulting in
a rather good seal. We have used that technique on the berm pond
drains as well. They are holding well with edpm liners as well.


Jim

"Gareee©" <gareee-> wrote in message
news: ...
> It dries very brittle, and just chips right off the rubbermaid. I did find
> a great simple waterproof seal though for adding a cap to t a toilet
> flange.. it fits on, but not waterproof, and I didn't want to glue it, in
> case I want to cannibalize parts down the road. A simple wrap of duct tape
> around worked great to seal the minute space there.
>
> Thinking of trying hot melt glue, or pvc glue next on the rubbermaid.
>
> Can't really assemble the rubbermaid filter without some gluing/sealing
> solution.
>
> --
> Gareee
> (Gary Tabar Jr.)
3M has a marine urethane sealant that I have heard good things about called
Fast Cure 5200. It is a moisture curing system that goes tack free in about
1 hour and completely cured in 24 hours. It is flexible and has better bond
than silicone. Apply it a little thick, loosely tighten to force some of
the sealant out all the way around the joint. After it has cured, tighten
the screws to force pressure on the material as a conforming gasket.

I'm thinking of trying the wax gaskets they actually use with the toilet
flanges... idea is to make the hole large enough to just accomodate the end
opening, and have the large part of the flage inside the rubbermaid... and
have one of the wax toiulet gaskets between the flange and the rubbermaid
wall.. with compression, the wax should seal the opening, it's VERY sticky,
so should grip the rubbermaid, and since there will always be water on them,
the temperatures should keep them cool. they are somewhat temperature
tolerant, I believe, and since they are wax, there shouldn;t be any
chemicals to leech out into the pond water.

Seems like a cheap and simple solution, after trying quite a number of
glue/gasket solutions.

If it works, I'll have discovered a neat cheap trick.. if not, I'm no worst
off.
--
Gareee
(Gary Tabar Jr.)

Clever. My only concerns would be heat melting it (sun) or it
hardening up and being moved somehow in the depth of winter.

Jim

Kurt wrote:

>In article <>,
> "Gareee©" <gareee-> wrote:
>
>
>
>>It dries very brittle, and just chips right off the rubbermaid. I did find a
>>great simple waterproof seal though for adding a cap to t a toilet flange..
>>it fits on, but not waterproof, and I didn't want to glue it, in case I want
>>to cannibalize parts down the road. A simple wrap of duct tape around worked
>>great to seal the minute space there.
>>
>>Thinking of trying hot melt glue, or pvc glue next on the rubbermaid.
>>
>>Can't really assemble the rubbermaid filter without some gluing/sealing
>>solution.
>>
>>
>
>How about a good silicone glue? (Like aquarium sealer)
>
>
>

I used aquarium sealer on the Rubbermaid stock tank for my Skippy filter
and it's worked well. I liked the aquarium sealer because, if
directions are followed, it is safe for the fish.
Gabrielle

Ok, here's what I learned today:

Just when you think you remember that toilet wax not being "too bad" to mess
with, you use it again and hate the stuff.. LOL Sticky, and nasty.

Good news, it worked flawlessly, from what I can tell. No leaks at all, and
connects are solid.

Might need to add a 4" elbow and line down from the outlet on top.. the
accordion 4" drainage hose/pipe puts more weight on that top flange then I'd
like. idf I do, I'll put a 90 degree elbow on it, and then run the 4" pvc
down th efront, and then put another elbow on it to make it reach the pond
better.

Bad news, is the gorilla glue that looked liek it sealed the 3/4 inch pvc
water inlet didn't.when the rubbermaid filled, it buldged, the gorilla glue
let go, and had a big nasty leak there. that will have to attached
differently. Might look into that aquarium glue that's been mentioned. I
already have shoe goo and silicon sealer.. wonder if it's different from
those?

So I had partial success today. I think when building something liek this,
it's be much better to find something with thicker plastic then a rubbermaid
trash can,.. even the 50 gallon ones have thin walls for attaching fittings.

--
Gareee
(Gary Tabar Jr.)

In article < .com>,
Phyllis and Jim <> wrote:

> Clever. My only concerns would be heat melting it (sun) or it
> hardening up and being moved somehow in the depth of winter.
>
> Jim

Aquarium silicone sealer will handle all temps, always be watertight and
is safe for fish. It's also inexpensive.

--
To reply by email, remove the word "space"

In article <>,
Ralph & His Clowder <> wrote:

> Kurt wrote:
>
> >In article <>,
> > "Gareee©" <gareee-> wrote:
> >
> >
> >
> >>It dries very brittle, and just chips right off the rubbermaid. I did find
> >>a
> >>great simple waterproof seal though for adding a cap to t a toilet flange..
> >>it fits on, but not waterproof, and I didn't want to glue it, in case I
> >>want
> >>to cannibalize parts down the road. A simple wrap of duct tape around
> >>worked
> >>great to seal the minute space there.
> >>
> >>Thinking of trying hot melt glue, or pvc glue next on the rubbermaid.
> >>
> >>Can't really assemble the rubbermaid filter without some gluing/sealing
> >>solution.
> >>
> >>
> >
> >How about a good silicone glue? (Like aquarium sealer)
> >
> >
> >
>
> I used aquarium sealer on the Rubbermaid stock tank for my Skippy filter
> and it's worked well. I liked the aquarium sealer because, if
> directions are followed, it is safe for the fish.
> Gabrielle

That's why I use it.

--
To reply by email, remove the word "space"